printer and another guide

Warning, this is a spoof video. The ink level indicator is controlled by the green computer chip. Doing anything else on the cartridge itself (as shown in the video), will not change the ink level.

Methode Reset Waste Ink Counter for Canon Printers BJC series

Canon BJ-30 BJC-35v BJC-70 Printers reset methode (F14 Error Reset)

1. Unplug adapter
2. Hold POWER
3. Plug in ADAPTER
4. Release POWER after printer starts
5. Hold FF and MENU and press POWER
6. Release after beeps
7. Press <> Cartridge until 1A is displayed
8. Press ONLINE
9. Press POWER to shutoff printer
10. Unplug printer then re-plug printer
    

Canon BJC-50, BJC-55, BJC-80, BJC-85, Printers Waste Ink Tank Counter Reset Methode

1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons after the printers starts up
5. Hold CARTRIDGE and RESUME
6. Press POWER
7. Release all buttons after the beeps
8. Press CARTRIDGE 16 times
9. Press RESUME
10. Unplug the Power cord
    

Canon Printers BJC-210 BJC-240 BJC-250 BJC-255 BJC-265BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650 Waste Ink Reset

1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5. Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME
    

Canon BJC-600 BJC-600e BJC-610 BJC-620 Printers

1. Unplug Power Cord
2. Hold POWER and FF and Print Mode buttons
3. Plug in Power Cord
4. Release after the beeps
   

Canon BJC-2000 BJC-2100 Printers Waste Ink Counter Reset

1. Remove the Cartridge
2. Unplug the AC Power Cord
3. Close Front access panel
4. Hold down the RESUME/RESET button and plug in the AC power cord
5. Release RESUME/RESET after plugging in the AC Power cord.
6. Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
7. Press and HOLD RESUME/RESET for two seconds or more and release it.
8. Press and HOLD RESUME/RESET for two seconds or more and release it.
9. Unplug AC Power Cord to set data.
   

Canon BJC-5000 Waste Ink Counter Reset

1. Power off printer
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
5. Press Power to set data
   

Service Test Print

• Power off printer
• Press and hold RESUME then press POWER, The indicator will start blinking.
• While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
• When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
• Press Power to Print
  

Nozzle Print

• Power off printer
• Press and POWER, until the printer beeps and release.
  

Demonstration Print

• While the printer in ON, Press and hold RESUME until the printer plays a melody of beeps.

Manual Service for Canon BJC-5100 Printes to Reset Waste Ink Counter

Self Test

• Switch Printer off. Hold Power for 1 beep.

Waste Counter Reset Canon BJC-5100

1. Power off printer
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
5. Press Power to set data
   

Service Test Print Canon BJC-5100

1. Power off printer
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
5. Press Power to Print
   

Nozzle Print Canon BJC-5100

1. Power off printer
2. Press and POWER, until the printer beeps and release.
   

Demonstration Print

• While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

Canon BJC-3000, BJC-6000, BJC-6100, BJC-6200, BJC-7000, BJC-7100, BJC-8000 Printers

1. Power off printer
2. Hold Resume button then press and hold POWER, the beeper will sound once.
3. Hold POWER and release RESUME
4. Press RESUME twice
5. When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6. Press Power to set data

This is how to reset your epson c90

1. Download Adjustment Program for Epson C90
2. Change your PC Date to Jul 24 2007
3. Delete the folder C:Adjustments_Programs on your PC if it exists.
4. Reboot your PC.
5. UNZIP file C90.rar.
6. RUN AdjProg.exe file.!

to Reset Waste Ink Counter

* RUN AdjProg.exe file Epson C90
* choose Particular adjustment mode
* select waste Ink pad counter
* Klikinitialization
download software resetter epson c90 here

1. Refill your cartridge using your Mr. Ink Jet refill kit.
2. Following the diagram at right, place a piece of adhesive tape covering the Click here to enlarge only the four blue colored contacts (a contact is the individual copper square). Make sure that only those four are covered and no others. *Please note that the contacts shown are colored for illustrative purposes only. You will not have blue or red contacts on your cartridge.

3. Place cartridge in the printer. The printer may tell you that there is a problem with your cartridge. Ignore this message. The printer may print an alignment page. If so, allow it to do so.

4. Take the cartridge out of the printer. Remove the tape from the four blue contacts. Place the tape over the four red colored contacts. Make sure that only those four are covered and no others. *Please note that the contacts shown are colored for illustrative purposes only. You will not have blue or red contacts on your cartridge.

5. Follow step 3 again.

6. Take the cartridge out of the printer for the final time. Take the remaining tape off and place back in the printer. The printer should print out an alignment page and the estimated ink level in the toolbox should read full.

Reset Method 2:

1. Refill your cartridge using your Mr. Ink Jet refill kit.

2. Following the diagram at right, place a piece of adhesive tape covering the only the blue colored contact (a contact is the individual copper square). Make sure that only that contact is covered and no others. *Please note that the contacts shown are colored for illustrative purposes only. You will not have blue or red contacts on your cartridge.

3. Place cartridge in the printer. The printer may tell you that there is a problem with your cartridge. Ignore this message. The printer may print an alignment page. If so, allow it to do so.

4. Take the cartridge out of the printer. Leave the tape from blue contact. Place another piece of tape over the red colored contact. Make sure that only that contact is covered and no others. *Please note that the contacts shown are colored for illustrative purposes only. You will not have blue or red contacts on your cartridge.

5. Follow step 3 again.

6. Take the cartridge out of the printer for the final time. Take the remaining tape off and place back in the printer. The printer should print out an alignment page and the estimated ink level in the toolbox should read full.

Reset Method 3:

If neither of the reset methods above worked, you can cycle cartridges through to reset the level. You will need two extra cartridges and the one you refilled. First, put the refilled cartridge in the printer. Allow it to recognize the cartridge and print an alignment page. Take that cartridge out and place in the first extra cartridge. Allow it to recognize and print an alignment page. Take the first extra cartridge out and place the second extra cartridge in. Allow it to recognize and print an alignment page. Take the second extra cartridge out. Place the refilled cartridge back in the printer. It will print an alignment page and then the estimated ink level will be reset to full.

Resetting Ink-Waste Overflow Counter Canon Pixma iP3000, iP4000, iP5000 Printers

• With the printer plugged in and powered off, press and hold the Resume/Cancel button, then press and hold the Power button. (DO NOT release the buttons. The LED light should be green to indicate that a function is selectable.).

• While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button)

• While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange)

• When the LED light is green, press the Resume/Cancel button 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange)

• Press the Power button. The LED lights in green, and the reset is performed. (When the operation completes, the printer returns to the menu selection mode automatically)

• Press the power button to exit service mode.

Note:
if you accidentally press the Resume/Cancel button more than 4 times in step 4 then just press the Resume/Cancel button at least 10 times and the printer will be returned to step 4 automatically

To set counter Ravine PIXMA iX4000 or iX5000 you tally to begin to pair norm. Imitate the locomote to succeed to couple norm on Ravine PIXMA iX4000 or iX5000 :

1. Link the Ravine PIXMA iX5000 or iX4000 machine to the knowledge fabric. ( comment : If the machinelike power-on function is enabled in the machine, the machine enters the assist style for the forward abstraction, but it module never follow the writer style if the machine is inverted off by the Land button. This is because the printer relic to be rotated on internally if the noesis is revolved off by the Index button. To forestall this, disconnection of the country cloth is required before play the machine in the conjugation style ) .
2. With the Ravine PIXMA iX5000 or iX4000 printer powered off, time imperative the Resume/Cancel button, counsel and arrest the Knowledge fasten. (mention : Dont discharge the buttons. The Knowledge LED lights in green to represent that a run is selectable.)
3. Time holding the Land fix, channel Resume/Cancel switch. (Dont transport the Superpower switch.)
4. Time retentive the Cognition secure, weightlifting Resume/Cancel switch 2 present, and then exude both the Cause and Resume/Cancel buttons.
5. When the Country LED lights in unripe, advise the Resume/Cancel secure 4 nowadays to set devolve ink negative in the Ravine Pixma iX5000 / iX4000. (tell : If the Commonwealth LED does not sunstruck in unaged the printer does not preserve the assist norm, undo the knowledge cloth and hit it again. Then start from rank 1 to start the machine in the force property again).
6. At the end of the personnel property, pressure the Knowledge add. The stuff lifting scale of the artifact give thing module be upraised.

Notation :

* Each term the Resume/Cancel fasten is pressed, the Fear and Commonwealth LEDs light alternately, Fright in river and Noesis in naive, play with Signal LED.

haii guys... this is my blog, i dedicated for you that need help printer trouble shooting

Waste Ink Counter Reset Manual for Service mode
Step 1:
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

Step 2 :
Software for Permanant (1st method)
1. Reconnect the USB cable and turn ON your Printer
2. Open "General Tools for iP1000"